Car keys · Richmond Hill
Ignition Lock Repair
Half the key is still in your hand.
In plain words
A key that has snapped off inside the ignition barrel is not the end of the key, or of the barrel. The broken piece is drawn out with hooked or spiral tools built for the job, without pushing it further in, and the cylinder is checked afterward for the wear that likely caused the break in the first place. A fresh key is then cut and tested before the visit ends.
How the visit goesHalf the key is still in your hand. The other half stayed behind in the ignition when it snapped, and now the dash won't light and the wheel won't unlock no matter how carefully you nudge what is left.
Ignition Lock Repair
How the visit goes
Separating a worn key from a worn cylinder
A spare key, even an old one, answers a question a single key cannot. If the spare turns the ignition smoothly while the regular key struggles, the key itself is the likely problem, rounded edges no longer lifting the internal wafers the way a crisp cut does. If both keys behave the same way in the barrel, the wear sits inside the cylinder instead. Where no spare exists, the locksmith reads the wafers directly with a decoder, which settles the question without waiting on a second key to test it.
Servicing the cylinder in place first
The first option is always the least invasive one: cleaning out the keyway, freeing a wafer that has stuck in a raised position, and lubricating the mechanism so the existing cylinder goes back to turning the way it should. This keeps the original hardware on the vehicle and avoids cutting a new key altogether when the fault turns out to be wear or contamination rather than a broken part. Only when this fails to restore normal behaviour does the barrel come out of the column.
A cylinder and key with a clean history behind them
Where the ignition showed signs of an earlier forced attempt, the replacement hardware carries none of that history forward: new pins, a new key, and a housing that has not been tampered with. You are shown the old part before it is handed over or taken away, so the vehicle's ignition starts its next chapter with hardware nobody has already tried once to defeat.
Ignition Lock Repair
In the van
Trim clips and fasteners
Broken key extractors
Steering column trim tools
Key blanks and cutting machine
Dry graphite or PTFE lubricant
Ignition Lock Repair
What affects the quote
Time needed to test every position
Cycling the ignition through every switch position and the steering lock, more than once, with the engine started and stopped to confirm the repair holds, adds a small amount of time on top of the repair.
Weather and road conditions on the day
A barrel packed with road salt, grit or old grease from a rough season takes longer to clean and free than one that has simply worn with ordinary use over the years of driving.
Vehicle make, model and column design
How the ignition assembly is built varies by vehicle, a simple housing reached with a few steps, or a column locked down with shear bolts and trim that has to come off carefully. That difference in access shapes how much time the repair takes.
What to have ready
- What is the vehicle's year, make and model?
- Has anyone already tried to force the lock?
- Do you have a spare or second key available?
Ignition Lock Repair: questions
QuestionsDo you need to confirm that I own the vehicle before starting?
Yes, and it takes only a moment when the paperwork is on hand. A vehicle permit or registration document matched to identification settles it in most cases. If the vehicle is a rental, a fleet vehicle or belongs to someone else, a lease, a work order or a call to the registered owner fills the gap. This step protects every vehicle owner who might one day call about their own ignition.
What is the difference between this and being locked out of my car?
A lockout is about getting into a vehicle that is closed against you; ignition lock repair is about the mechanism the key turns once you are already inside or once the door is open. The two sometimes happen together, a stuck ignition can follow a lockout, but a working ignition and a locked door are separate problems with separate tools and separate visits to arrange.
What is actually different between ignition lock repair and dealer key programming?
The lock cylinder is mechanical: a key physically turns it through accessory, on and start. The immobilizer and transponder system is electronic: it recognises a chip inside the key before allowing the engine to run. A locksmith services or replaces the physical cylinder; programming a chip to the vehicle's electronic system is separate work that a suitably equipped automotive locksmith, a dealer, or an automotive electrical specialist can handle.
Related services
- Car Key ReplacementAfter fifteen years the blade has worn to a smooth sliver.
- Spare Car Key DuplicationA lockout last month ended with a locksmith opening the door and going home, and the same single key has been carried ever since with nothing behind it.
- Key Fob ProgrammingA new driver has joined the household, and the one existing fob is the only key anyone has ever had cut for this vehicle.